Kas ir piesardzības pasākumi par darbība of iesmidzināšana formēšana mašīna

Do you understand the precautions of injection molding machine operation? If you don't know, let's go with Xiaobian to understand it.
Iesmidzināšana formēšana mašīna darbība piesardzības pasākumi:
1. The Power switch of the motor and electric heating must be shutdown off before power transmission.
2. Pārbaude vai cirkulācija dzesēšana ūdens ir gluds. Kad iedarbināšana un apkure mašīna, nodrošina ka vārsts of the cirkulācija dzesēšana ūdens of hidrauliskā eļļa un cilindrs ir atvērts un gluds.
3, The Machine IS Equipped Ar A Centralized Eļļošana Device, Before Starting The Machine, Check The Amount Of Oil In The Device, Before The Oil Level Falls To Open The Warning Line, To Refill The Ieeļļošana eļļa, Inject Oil to the Specified Oil Level.
4, when the machine starts, first use the point start (that is, press the motor start button, the motor starts, and then disconnect, 1-2 seconds later, and then repeat the point start and disconnect 3 to 4 times. When the oil pump and the motor turn, listen to the abnormal noise, and stop the operation immediately immediately if there is abnormal noise.
5, check the parameters of the machine in operation, first put the machine in the manual state, press the relevant button, visual pressure gauge, you can predict the pressure of each section, when the electric heating is not heated to the set value (normal operation temperature), remember not to start the hydraulic motor, operation feeding, injection, ejectivity and other actions, otherwise it may lead to mašīna kļūme vai bojājumi.
6, the first two closing buttons (left, right each, green) must be operated with both hands at the same time, it is strictly forbidden to one-handed operation: (that is, to press one of the buttons with the object fixed first, so that the button is in the conduction state, and then only use the other button to operate the mode lock, who will cause broken hands.)
7. In pārbaude un regulēšana funkcionālie parametri of the injection molding machine, the power supply of motors un eļļa sūknis vajadzētu jāgriež izslēgts as far as iespējams. Ja it ir nenovēršams, special care vajadzētu be take. It is strictly forbidden operate the keys on the control board of the machine with one hand, while other hand does any work or touches any moveing parts on the machine ietvaros tvērums of the locking mold area. It is absolūti aizliegts par diviem cilvēkiem to operate a machine: (tas ir, one persona darbojas atslēgas on the control board of the machine, while the other person operates or touches the move parts in the scope of the locking mold area)
8, operation of horizontal injection molding machine: when the safety door is opened, it must be confirmed that the stop block can automatically fall in the mold stop position, do not move the bumper. Stop block or bumper cover, when the machine in the mold stop and not to the endination position, the mechanical safety device is not effective, to understand its critical.
9, check the safe operation of the machine: the machine is in the manual state, press the opening button, let the machine completely open the mold to the endination position, then observe whether the machine open the mold termination position is in the set position, if the opening mold exceeds the set endination position, the the mechanical failure, the machine can not work;
10, In The Inspection of the Machine or do any work on the machine, before touching any Moving parts, Pressure Electric Parts, Be Sure to Remember the Problem of safe operation, Be sure to cut off the Power Supply of the oil pump motor to Ensure safety safety.
11, KAD SPRAUSLA (sprausla) IS virzība (krīt), Do Not Remove the Nozzle (Sprausla) siekalošanās sveķi ar kailām rokām vajadzētu stop the injection molding, and use dzelzs knaibles (skava) to Remove the tool, Not To Operate directly ar Jūsu roku.
12, izslēgšana In pabeigšana darbs vai kad a pēkšņa barošana atteice, for the sake of safety and protection of electrical equipment, the power switch should be atvienots.
Remember: Failure to follow the above specific operation procedures may result in serious hazards and machine failure.